GPIO Interface RFID Fixed Reader With RS232 Wiegand Auto Running

High performance 4 ports UHF RFID fixed reader with rs232,rs485 ,wiegand ,GPIO interface

ZK_RFID406 is a high performance UHF RFID fixed reader. It is designed upon fully self-intellectual property. Based on proprietory efficient digital signal processing algorithm, it supports fast tag read/write operation with high identification rate. It can be widely applied in many RFID application systems such as logistics, access control, anti-counterfeit and industrial production process control system.

Specification:

FEATURES:

 Self-intellectual property;
 Designed with Impinj R2000 RFID engine;
 Support ISO18000-6C(EPC C1G2) , ISO18000-6B protocol tag;
 860~868MHz/902~928MHz frequency band(frequency customization optional);
 FHSS or Fix Frequency transmission;
 RF output power up to 30dbm(adjustable);
 4 TNC antenna port with antenna auto-tuning and failure-detection;
 Support auto-running, answer, trigger and real-time-inventory work mode;
 Tag buffer size up to 800PCS (Max. 496bits EPC length);
 Support EPC and TID inventory;
 Low power dissipation with single +9 DC power supply;
 Support RS232, RS485, RJ45(TCPIP) with WiFi and POE optional;
 High reliability design;
 Support on-the-site firmware upgrading and optional Wince or Linux Operation System.

CHARACTERISTICS
 Absolute Maximum Rating
ITEM SYMBOL VALUE UNIT
Power Supply VCC 16 V
Operating Temp. TOPR -10~+60 ℃
Storage Temp. TSTR -20~+75 ℃

 Electrical and Mechanical Specification
Under TA＝25℃,VCC＝+9V unless specified
ITEM SYMBOL MIN TYP MAX UNIT
Power Supply VCC 8 9 12 V
Current Dissipation IC 800 1500 mA
Frequency FREQ 902 902~928 928 MHz
Size Size 310×210×41 mm

MECHANICAL DATA(UNIT mm):

INTERFACE

1．Power J1
No. Symbol Comment
2 PWR +9VDC
4 GND Ground
1,3 NC Reserved
2．WiFi Antenna J2 (SMA Female)
3. USB J3 (Slave)
4. USB J4 (Reserved)
5. TCPIP RJ45 Socket J5
6. UART J6 (RS232 DB9 Female)
No. Symbol Comment
1 NC Reserved
2 TXD Data output in RS232
3 RXD Data input in RS232
4 NC Reserved
5 GND Ground
6 NC Reserved
7 NC Reserved
8 NC Reserved
9 NC Reserved

7. GPIO J7 (DB15 Female)
No. Symbol Comment
1 Output1 General output1
2 Output2 General output2
3 Output3 General output3
4 Output4 General output4
5 Input1 General Intput1 with Internal 47k resistor pulled-down to ground
6 Input2 General Intput2 with Internal 47k resistor pulled-down to ground
7 Input3 General Intput3 with Internal 47k resistor pulled-down to ground
8 Input4 General Intput4 with Internal 47k resistor pulled-down to ground
9 TGIN Trigger input with internal 10k resistor pulled-up to +5V
10 R+ R+ in RS485
11 R- R- in RS485
12 GND Ground
13 NC Normal-Close terminal of internal relay
14 NO Normal-Open terminal of internal relay
15 CM Common terminal of internal relay

8．TNC Antenna Port1~Port4 J8~J11

9．LED indicator
Symbol Comment
POWER Power on indicator
RUN Command-executing indicator
TAG Tag-detected indicator
WIRELESS WiFi active indicator
ALARM Alarm indicator
1~9 RSSI indicator

Remark:
1. Specifications are subject to change, please pay attention to our latest version.P